Home / Garden Projects and Outdoor Living

How to Build a Raised Bed with Landscape Timbers: The Stacked, Spiked Frame

A lush vegetable garden of cabbage and strawberry plants growing in beds

Photo: Luis Gallardo / Pexels

Landscape timbers are the raised bed material of least resistance: cheap, stocked at every home center, light enough to carry under one arm, and forgiving of a beginner's saw work. A bed built from them is a small log wall, and it stands or fails by log wall rules. Each timber is about 3.5 inches tall in the stack, so the classic bed is 3 courses, roughly 10.5 inches of wall holding 9 to 10 inches of soil, which suits nearly every vegetable grown. The corners must overlap, each course alternating which side runs long, so the stack locks itself together instead of standing as four separate walls leaning on nails. The joints within each course must stagger against the course below. And the finished frame must be pinned to the earth, with galvanized spikes or rebar driven through pre drilled holes, because a stack of timbers held only by its own weight walks apart a fraction every freeze and thaw until the corners open. The checklist tracker on this page sequences the build; the sections below carry the details that decide whether the bed is square and tight in year five or a parallelogram of gaps in year two.

Interactive tool

Landscape Timber Raised Bed Build Checklist

Check off each step as you finish it. Your progress stays on this page.

0 of 8 complete

0% done

Layout, Leveling, and the First Course

Mark the bed's rectangle with string lines and check it square by measuring the diagonals until they are equal, because a timber bed announces its geometry honestly and a bed 2 inches out of square shows it in every corner overlap. Strip the turf and level the footprint, then set the first course directly on the leveled soil or, better, on a shallow bed of tamped gravel that keeps the bottom timbers out of standing water. The first course is the foundation and gets the ritual: level along every side, level across, square again, because every later course copies it. Landscape timbers are rarely perfectly straight, so sort the pile: the straightest timbers go in the first course and the visible front, the bowed ones get cut for the short ends or buried in the back, with any bow oriented upward so soil pressure and the spikes can pull it down rather than letting it lift a corner. Cut with a circular saw or a handsaw and treat every cut end with preservative, because the factory treatment does not penetrate the heartwood and a fresh cut face is the bed's first rot site.

Corners, Joints, and the Spike Pattern

Build the corners Lincoln log fashion: on the first course the front and back timbers run full length and the side timbers butt between them; on the second course the sides run long and the front and back butt in, alternating every course so the corner is a woven stack of timber ends. Fasten each corner with a long screw or spike driven vertically through the overlap. Within a course, where a long side needs two timbers, butt them tightly and make sure that butt joint lands at a different position than the joints in the courses above and below, staggering by at least 4 inches and ideally by feet, because aligned joints make a vertical seam the soil pressure works on like a zipper. When the stack reaches full height, pin it: drill pilot holes down through the courses near each corner and at intervals along the long sides, and drive 10 to 12 inch galvanized spikes, or half inch rebar cut to length, through the stack and at least several inches into the ground. Pre drilling is not optional in dry hardwood or near a timber's end, where a driven spike splits the wood it was meant to hold. Cap the spikes flush or slightly below the top face so no shin or kneeling knee ever finds one.

Strawberries spilling over a wooden bed edge
Strawberries spilling over a wooden bed edge

The Treated Wood Question, Answered Straight

Modern landscape timbers are pressure treated, and the question every food gardener asks deserves the direct answer the extension services give. The old CCA treatment, chromated copper arsenate, was withdrawn from residential use in 2003, and the timbers sold today use copper based treatments such as ACQ and copper azole, in which copper is the active ingredient. Copper migrates into soil in small amounts, mostly within an inch or two of the wood, and plants take up very little of it; university extension guidance treats modern treated timber as acceptable around food gardens, while gardeners who want a margin can take the cheap one: line the inside faces of the bed with a durable landscape fabric or heavy plastic stapled to the wood, keeping soil off the timber entirely, which also slows the wood's own decay. The liner rule on this page is therefore simple: line a food bed, skip the liner in a flower bed, and never burn offcuts, since treated wood ash concentrates everything the treatment put in. Railroad ties are not a variety of landscape timber and get their own verdict: they are soaked in creosote, which bleeds in summer heat, smells, and is unwelcome near food soil by any standard; a tie wall belongs in landscape terracing away from the vegetable garden, not in a bed whose soil feeds people.

Fill, and the Bed's Working Life

Fill the finished frame in lifts with a raised bed mix, roughly two thirds topsoil or bagged bed blend to one third compost, watering each lift to settle it, and expect the surface to drop an inch or two in the first season as the mix consolidates; top up with compost each spring, which is also the bed's fertility program. A 4 by 8 foot bed at 3 courses holds roughly three quarters of a cubic yard of mix at working depth, a number worth having before the soil run, and the site's raised bed soil calculator guide works the arithmetic for other sizes. The bed's honest service life is 7 to 12 years depending on climate and timber quality, with failure arriving at the soil line of the bottom course and at untreated cut ends, which is why the gravel footing and the end grain preservative in the first section are worth their hour. Inspect each spring by pushing a screwdriver into the bottom course at a few points; soft, punky wood on one side can be replaced by jacking that side, sliding the timber out, and sliding a new one in, a repair the stacked design makes genuinely possible and one more reason the system endures. Compare the alternatives on this site before buying: the railway sleeper raised bed guide and the brick and cinder block builds trade the timber bed's speed for permanence, and the paver flower bed build runs the dry stack logic in stone.

Variations on the Stack: Height, Width, and Tiers

The 3 course rectangle is the standard, not the limit, and the same rules scale. A 2 course bed at about 7 inches serves salads, herbs, and flowers where the native soil beneath is decent, since roots continue into the ground below the frame, and it builds in under an hour. A 4 course bed at about 14 inches suits deep rooted crops and gardeners who would rather bend less, and it demands the pinning step without exception, because the taller the stack, the more leverage the soil has against the corners. Width follows reach: 4 feet for a bed accessed from both sides, 2 to 3 feet against a fence or wall, and any length the yard allows, with a cross brace or an extra pinned joint every 8 feet on long runs to keep the sides from bowing outward under the soil's steady push. Tiered beds on a slope are simply the stack stepped: each tier is its own level rectangle sharing a wall with the next, built from the bottom up, and the timber system handles the job more gracefully than any other material in its price class, because each step is just another course decision. Whatever the variation, the constants do not change: level first course, woven corners, staggered joints, preservative on cut ends, and pins through the stack into the ground.

Related guides

These guides sit closest to this one on the garden path:

Frequently Asked Questions

How many landscape timbers do I need for a 4 by 8 foot bed?

Each timber is 8 feet long and adds about 3.5 inches of height. A 3 course 4 by 8 bed needs, per course, two 8 foot timbers and two 4 foot pieces cut from one more timber, so 3 timbers per course and 9 in total, plus one spare for a bowed or split piece. Buy 10 and sort the pile, straightest to the first course.

How tall is a raised bed made from landscape timbers?

About 3.5 inches per course. Two courses give roughly 7 inches, enough for shallow rooted flowers and salads; 3 courses give about 10.5 inches, the classic vegetable bed holding 9 to 10 inches of soil; 4 courses reach about 14 inches for deeper crops or a higher working position. Pin 3 and 4 course beds with spikes or rebar without fail.

Are pressure treated landscape timbers safe for vegetables?

Modern timbers use copper based treatments, the arsenic based CCA having left residential use in 2003, and extension guidance accepts them around food gardens. Copper migration into soil is small and mostly within an inch of the wood. For a full margin, line the inside faces of a food bed with landscape fabric or heavy plastic, which also extends the wood's life. Never burn the offcuts.

Can I use railroad ties instead of landscape timbers?

Not for food beds. Railroad ties are creosote soaked, bleed in summer heat, and are unwelcome near soil that feeds people under any guidance. They have a legitimate life in landscape terracing away from edible plantings. For a raised bed, buy landscape timbers, whose treatment is made for residential ground contact.

How do I stop the corners of a timber bed from opening up?

Build them overlapped, Lincoln log style, alternating which side runs long on each course, fasten each overlap with a long screw or spike, and pin the finished frame to the ground with spikes or rebar through pre drilled holes near the corners. Corners open when they are merely butted and nailed; the woven, pinned corner has nowhere to go.

Photo credits: Luis Gallardo (Pexels); Magda Ehlers (Pexels). Photos are served from this site; follow the credit to the library page for the original.